Dimmer CH-303

Connect Home 303 is a wireless high-voltage Z-Wave device that can be controlled using both standard switches and Z-Wave commands. CH-303 is a so-called “boxed product”. This means that you just need to take it out of the box, install it according to the wiring diagram, add a network to the Z-Wave and the device is ready to work. The device also has a wide range of adjustable parameters, compatible with all types of Z-Wave controllers. Z-Wave is the international wireless standard for smart homes. The standard uses a frequency of 868.42 MHz (for Europe) to realize a very stable and secure connection. Each Z-Wave node on the network can act as a repeater for other nodes (mesh network) if the recipient is not in direct wireless range of the transmitter. 1. SPECIFICATIONS 2. PRODUCT APPLICATION 3. DEVICE CONNECTION 4. CONNECTION GROUPS 5. PARAMETERS 6. OPERATING PARAMETERS OF BUTTONS/SWITCHES 7. MANUFACTURER'S WARRANTY 1. Specifications Table 1 Rated supply voltage 110 - 250 V AC 50/60Hz -10°C to +50°C Radio signal power 2 mW Radio frequency 868.4 MHz EU; Indoor range up to 45 m Outdoor range up to 75 m Power consumption < 1.3 W Module dimensions (H * W * D) 18 mm * 48 mm * 37 mm Degree of protection CH-303 IP-30 cos ? - this is a dimensionless quantity that determines the quantitative ratio of the consumed electricity, which performs useful work to the full power. Load capacity for exposure cos ?=1 - the coefficient of dimmable LED and CFL lamps is in the range cos ? = 0.4 - 0. 95. Recommended power values ​​for various lamps: Table 2 Lamp types Power (W) Ohmic incandescent lamp (halogen lamp) (cos ? = 1) 200 W * cos ? Inductive twisted transformer for low-voltage halogen lamps (cos ? = 1) 150 W * cos ? Capacitive twisted transformer for low-voltage halogen lamps (cos ? = 0.5) 130 W * cos ? LED lamps and LED lighting devices (cos ? = 0.95 to 0.4) 100 W * cos ? 2. Product Application The CH-303 module is a Z-Wave device that is used for smooth dimming (dimming). The device itself can determine the power of the connected load and has a wide range of dimming speed. 3. Connecting the device Follow the safety rules during installation / dismantling of the device for Ukraine “DNAOP 0.00-1.32-01” for Russia this is the “PUE” seventh edition. Before starting installation, it is necessary to de-energize the electrical network, and protection against accidental switching on of voltage in the network must also be provided. Electrical work must be carried out by a qualified electrician in accordance with current codes and regulations. If problems arise or if it is not possible to ensure the safe work of the installer during installation, immediately disconnect the device and equipment connected to it. Installation and connection The dimensions of the module allow the device to fit into a standard installation box with a diameter of 60 mm and a depth of 45 mm behind your circuit breaker. Before installation, turn off the power supply, connect the module according to the wiring diagram. Please note that during normal operation, the module generates little heat. Take measures to ensure normal heat dissipation. Do not install several modules together in a limited space, do not allow the module to be placed in thermal insulation materials. Example of installing the module in a European socket Figure 1. Figure 1 It is possible to connect the device in two ways: with and without a neutral wire. Wiring diagram without neutral wire. Figure 2 The figure indicates Figure 2: N - Neutral wire; L - Phase; ~ - Output to the load; S1 - Contact for Switch No. 1; S2 - Contact for Switch #2. Wiring diagram with neutral wire. Figure 3 The figure indicates Figure 3: N - Neutral wire; L - Phase; ~ - Output to the load; S1 - Contact for Switch No. 1; S2 - Contact for Switch #2. To start working with the device in the Z Wave network, switch the controller to the add mode as shown in the instruction of your controller Figure 4. Figure 4 Then press the system button three times to start adding Figure 5. Figure 5 Then configure the connection groups and parameters at your discretion according to the paragraphs 4 and 5. To delete a device, put the controller in delete mode and press the system button three times. 4. Communication groups Z-Wave devices can interact with each other, as well as exchange data and other information, both with the central controller and directly without the participation of the controller. Each event can have its own list of recipients, called a link group. Refer to your Z-Wave controller's user manual for link settings. Link groups CH 303 figure 6: Group 1 – device (controller recommended) that will receive reports on dimmer state changes. Group size - 1 device. Group 2 - devices that will receive the On / Off command when the switch connected to contact S1 is pressed. The group size is 10 devices. Group 3 - devices that will receive a command to dim while holding the switch connected to contact S1. The group size is 10 devices. Group 4 - devices that will receive the On / Off command when the switch connected to contact S2 is pressed. The group size is 10 devices. Group 5 - devices that will receive a command to dim when holding the switch connected to contact S2. The group size is 10 devices. Figure 6 5. Parameters You can fine-tune the device using a number of configuration parameters. .Parameter No. 1 - Automatic calibration. Automatic calibration is necessary in case of changing the lamps connected to the dimmer. During the calibration process, the lamp will turn on at 100% and then turn off. The parameter will automatically return to the default value after a successful calibration process 0. (Default) Normal operation of the device 1. Calibration process. Parameter number 2 - Minimum brightness level. A parameter that specifies a value for the minimum brightness. Valid value is 1 to 94. 1. (Default). Parameter number 3 - The maximum brightness level. An option that specifies a value for maximum brightness. Valid value is from 6 to 99. 99. (Default). Parameter #4 - Dimming speed. A parameter that specifies the time it takes for the light to go from minimum to maximum brightness and vice versa. When the value “0” is selected in the parameter, the switching occurs instantly, dimming does not work. Units used in the parameter: 0 - 120 (1 = 1 second). 0. Instantly. 5. (Default). Parameter number 5 - Auto-shutdown with a delay. After receiving the turn-on signal, the device will automatically turn off after a certain time. When the parameter is set to “0”, auto-off does not work. Units used in the parameter: 1 - 650 (1 = 1 second). 0.  - (Default). Option #6 - Enable All/Disable All. The parameter allows you to configure whether the module will respond to the "Enable All" broadcast commands. and " Turn everything off. 0.  (Default) Respond to "Enable All" command, respond to "Disable All" command; 1.   Ignore "Enable All" command, ignore "Disable All" command; 2.  Ignore the "Enable All" command, respond to the "Disable All" command; 3.  Respond to the "Turn on all" command, ignore the "Turn off all" command. Parameter No. 7 - Restoring the state of the device after a power failure. If you want the device to restore its previous state after an electrical failure, select "Restore". If you want the device to be turned off, after an electrical failure, select "Do not restore". 0.  (Default) Restore 1.   Do not restore. After power on, the device will be in the "Off" state. Parameter No. 8 - Type of load. The parameter allows you to configure whether the module will respond to the "Enable All" broadcast commands. and "Turn everything off". 0.  (Default) Dimmable Load 1.   Non-Dimmable Load Parameter #13 - Smart Delay After receiving a turn off signal, the dimmer will turn off not immediately, but after a certain time. In Parameter #14 you can select the cases in which the dimmer will ignore the Smart Delay. Valid value is 1-1800 (1 = 1 second); 0.  (Default) Parameter #14 - Smart Delay Setting. This parameter will allow you to configure the "Smart Delay" in more detail. The module can receive an on/off command from: - local switches - controller (device from the 1st connection group); - other devices using connections; 0.  Respond to "Smart Delay" (Parameter 13), no matter how the "Shutdown" command is received; 1.   (Default) Respond to "Smart Delay" in cases of receiving a "Shutdown" command from: - Devices that are not in the 1st link group; In case of receiving a shutdown command from the local Switch S1 or the controller, the module will turn off instantly. 2.  Respond to "Smart-delay" in cases of receiving the "Turn off" command from: - Devices that are not in the 1st communication group; When receiving a "Turn On" command from a local switch or controller, the dimmer will stop interacting with the sensor and will not turn off until it receives a "Turn Off" command from the local switch or controller. 6. Parameters of operation of buttons/switches The module has the ability to connect one or two switches to it. The first switch can control the module directly, and up to ten devices can be connected to it (using the 2nd link group). The second switch is used exclusively to control other devices (up to 10 devices) connected to it via the 3rd communication group. Parameter #16 - Switching mode for Switch 1. Monostable - for a return type switch or for a button, each press switches the device to the opposite state. Bistable - for conventional switches with two fixed positions On and Off. 0.  (Default) Monostable - in this mode, each subsequent press of the button switches the device to the opposite state. Monostable switches support dimmer control. When you press and hold the button of the monostable switch, the dimming start command will be sent to the dimmer, by releasing the button you can select the desired light level; 1. Bistable - each subsequent switching of the switch will change the state of the dimmer (on / off) regardless of the initial position of the key; 2. Bistable, fixed position (Option 1) (contacts on the switch are closed - dimmer on, open - dimmer off); It is necessary to take into account the fact that when the module receives a command from another Z-Wave network device, the relay will change its state and to control the switch, it must first be returned to the appropriate state. 3.  Bistable, fixed position (Option 2). Similar to the previous one, but vice versa (contacts on the switch are closed - the dimmer is off, open - the dimmer is on). 4.  Middle position switch. A switch with 2 monostable switches, one connected to S1 and the other to S2. The switch, which is connected to the contact S1 - turns on and dims the lighting "up" - increases the brightness. The switch, which is connected to contact S2 - turns off and dims the lighting "down" - reduces the brightness. Parameter #17 - Switch Mode for Switch 2 (Does not control dimmer). Monostable - for a return type switch or for a button, each press switches the device to the opposite state. Bistable - for conventional switches with two fixed positions On and Off. 0.  (Default) Monostable - in this mode, each subsequent press of the button switches the device to the opposite state. Monostable switches support dimmer control. When you press and hold the button of the monostable switch, the dimming start command will be sent to the dimmer, by releasing the button you can select the desired light level; 1. Bistable - each subsequent switching of the switch will change the state of the dimmer (on / off) regardless of the initial position of the key; 2. Bistable, fixed position (Option 1) (contacts on the switch are closed - dimmer on, open - dimmer off); It is necessary to take into account the fact that when the module receives a command from another Z-Wave network device, the relay will change its state and in order to control the switch, it must first be returned to the appropriate state. 3.  Bistable, fixed position (Option 2). Similar to the previous one, but vice versa (contacts on the switch are closed - the dimmer is off, open - the dimmer is on). Parameter No. 18 - Maximum light level by double pressing the switch The parameter goes to the maximum light level after double pressing the switch connected to contact S1. Sending such a command is possible only in the monostable mode of the switch (Parameter No. 16 - value 0). 0. The function is disabled; one. (Default) The feature is enabled. 7. Manufacturer's warranty Warranty period - 1 year from the date of sale. Products that were transported, stored, installed and operated in violation of the requirements for these products, as well as those that have mechanical damage, are not subject to warranty replacement. Do not use the device in any way other than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device. installed and operated in violation of the requirements for these products, as well as having mechanical damage - are not subject to warranty replacement. Do not use the device in any way other than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device. installed and operated in violation of the requirements for these products, as well as having mechanical damage - are not subject to warranty replacement. Do not use the device in any way other than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device.