IR module CH-501

ntroller is a device that is connected to the Internet, which allows you to control all devices remotely.3. SpecificationsRated supply voltage110 - 250 V AC 50/60HzOperating temperaturefrom -40°C to +80°CRadio signal power2 mWRadio signal frequency868.4 MHz EU;869.2 MHz RU;Indoor range up to 45 mOutdoor range up to 75 mPower consumption0.72WDimensions module18mm*48mm*37mm Degree of protection CH-202IP-304. Connecting and configuring the deviceAttention! This device is powered by 220 Volts 50 Hz. Follow the safety rules when mounting/dismantling the device. Before starting installation, it is necessary to de-energize the electrical network, and protection against accidental switching on of voltage in the network must also be provided. Electrical work must be carried out by a qualified electrician in accordance with current codes and regulations. If problems arise or if it is impossible to ensure the safe work of the installer during installation, immediately turn off the power to the device and the equipment connected to it. controller tab of the device and click the add button Figure 2. Figure 2 Triple click the system button several times to put the device into add mode. After successful addition, two widgets will appear in the room that you specified for the device Figure 3Figure 3After unplug the plug from the 220V socket, connect the device to the computer using a USB-microUSB data cable, connect the IR command transmitter Figure 1.Click on the link (Windows,  ;Linux,  Driver) to download the program Constructor Virtual Device Figure 4, click download then direct download.> Make sure that the USB cable leading to the device will not be accidentally hit during setup, in order to avoid accidental disconnection. Run the program, the device will be searched. If the search is successful, the image will appear Figure 5. If you are setting up the device for the first time or decide to overwrite it completely, click clear data. If you decide to reconfigure your device, click read data. Figure 5 In case of unsuccessful search, figure 6 Figure 6 Make sure the connection is intact. Make sure that your USB-microUSB cable is dated. Register and download the official Silicon Labs driver according to your system driver. Unpack the driver into a separate folder, run the installer depending on the bitness of your system CP210xVCPInstaller_x64/x86. Search for the device again. If the above steps did not help or if the problem occurs again. Go to Device Manager Figure 7, Ports, Silicon Labs, Properties, Driver and uninstall the driver. Remove the USB cable from the device and insert it back, repeat the search, in case of failure, reinstall the driver manually as described above. Figure 75. Working with the Virtual Panel Consrtuctor in itself: Figure 9 Elements seven types of elements to fill in commands; device ID; Panel contains panels in which are filled with elements to imitate the control panel; Modes in which the element is selected for teaching a command or issuing a command by an element; Settings in which elements are filled with commands. To get started, add your device ID from the controller in Figure 10 to the corresponding program fieldFigure 10Drag the elements to the panel to form the remote control you need Figure 11.Figure 11To fill in the element, click on it Figure 12.Figure 12In the settings, enter the name of the element (hereinafter the button) or the icon by which it will be displayed. You can hide the button if you don't like its current location by checking the hide field. press teach IR command and on the button you need from the remote control of your device. If successful, the image will appear Figure 13. After that, you can save the configuration (item 12) get the "Promto" code from the learned commands by clicking on the learned button. In the “Promto” commands, click get, a window will appear Figure 15. Figure 15 Click get and copy the command code. the line with the ID in this example is ID 19.Figure 16Enter the received ID in the Scene ID field and click add picture 17. Figure 17 It is possible to create a second panel Figure 18. To do this, click on the pencil icon 1 then Two Tab 2. After that, the second panel will appear. Figure 17 Save the configuration by clicking the menu, save as, select the save path, file name, save. Select the saved file and change its extension to “.json”. Go to the device setup menu in the controller and load the panel ConnectHome sensors. They can be of two types binary (for example: a motion sensor, it has only two values: there is movement / no movement) and multilevel (For example: a temperature sensor). Sensors are not included in the kit, if necessary, they can be purchased separately. List of ConnectHome sensors that can be connected to CH-501*: Binary sensorsMultilevel sensorsCH-S04.10 motion-light sensor (radius 10m.)CH-S01 temperature sensorCH-S02 temperature and humidity sensorCH-S06 power sensorAll sensors are connected to a special connector S- Bus located on the body of the device. Sensors are used to assess the environment in your home: temperature measurement; measurement of relative air humidity; illumination level; the presence of movement. In the Z-Wave network, sensors are displayed as structural units (endpoint) of the CH-501 module. Data is transmitted to the control controller via Z-Wave radio commands. Important! Only one ConnectHome sensor can be connected to the special S-Bus connector of the CH-501 device. The sensor must be connected before the module is connected to the Z-Wave network. If it becomes necessary to connect the sensor after connecting the module to the Z-Wave network, you must first remove it, and re-add it after connecting the sensor.7. Choosing a location for installing the IR module You can place the CH-501 module in any place convenient for you, but please note that the IR transmitter must be fixed in such a way that it is directed towards the IR receiver of the device that needs to be controlled.8. IR module controlThe IR module is a Z-Wave device designed to control any IR device by sending them IR commands. The module can be controlled using the Z-Wave commands of the main controller (see the main controller manual). CH-501 IR module, together with most Z-Wave controllers, form a full-featured digital device. With their help, you can not only set the desired room temperature, switch your favorite TV channels and control the audio system, but also do it automatically using any schedules. In addition, you will be able to control the system remotely using an Internet connection with your Z-Wave controller.9. Communications Z-Wave devices can interact with each other, as well as exchange data and other information, both with a central controller and directly without the participation of a controller. Each event can have its own list of recipients, called a link group. Refer to your Z-Wave controller's user manual to set up communications. CH-501 Communication Groups: Group 1  - the device (controller recommended) that will receive device status reports. Group size - 3 devices.10. Manufacturer's warranty The warranty period is 1 year from the date of sale. Products that were transported, stored, installed and operated in violation of the requirements for these products, as well as those with mechanical damage, are not subject to warranty replacement. It is not allowed to use the device in other ways than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device.< installed and operated in violation of the requirements for these products, as well as having mechanical damage, are not subject to warranty replacement. It is not allowed to use the device in other ways than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device.< installed and operated in violation of the requirements for these products, as well as having mechanical damage, are not subject to warranty replacement. It is not allowed to use the device in other ways than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device.< in case of non-observance of the operating rules, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device.< in case of non-observance of the operating rules, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device.<