CH-408 battery module - can control other Z-Wave devices using standard switches connected to it, and also has the ability to connect a CH-S01 temperature sensor. The device supports such commands as: turn on, turn off, dim, as well as start scenes on the central controller. 1. PRODUCT APPLICATION 2. MANUFACTURER'S WARRANTY 3. SPECIFICATIONS 4. Z-WAVE TECHNOLOGY IN BRIEF 5. DEVICE CONTROL 6. DEVICE CONNECTIVITY 7. COMMUNICATIONS 8. PARAMETERS 9. SCENES help links; Works from one battery within 4 years*; Has the ability to connect up to 8 switches; Works independently of the central controller; Signals low battery; Ease of setup and installation; It has the ability to connect a temperature-humidity sensor *provided that the switch is used 2 times per day. Complete set 1. Device CH-408 (version 2.4); 2. Battery 1/2 AA (ER14250) 3. Instruction. 1. Product use The CH-408 battery controller is a Z-Wave device that can control other Z-Wave network devices using up to 8 switches connected to it. The controller has the ability to connect one (two-wire) temperature sensor CH-S01L (The sensor is not included in the package, if necessary, it can be purchased separately). The device is powered by a 1/2 AA battery (ER14250) or an alternative power source 12-24V DC. CH-408 DEVICE SUPPORTS THE FOLLOWING COMMANDS: Turn on; Turn off; Turn on the set value; Sending multi-level commands to devices such as: dimmer, curtain control module, etc.; Sending preset scenes (Scene Activation Set). Consult your controller manual for support for such commands; 2. Manufacturer's warranty Warranty period - 1 year from the date of sale. Products that were transported, stored, installed and operated in violation of the requirements for these products, as well as having mechanical damage, are not subject to warranty replacement. Do not use the device in any way other than those specified in this manual. The manufacturer does not bear warranty obligations in case of non-compliance with the rules of operation, changes in the design or painting of the device. Immediately after opening the package, be sure to check the device for damage. If there is visible damage, do not connect or use the device. 3. Specifications Power supply: Battery 1/2 AA (ER14250); Alternative power supply 12-24V DC. Operating temperature 0?C to 40?C Radio signal strength 2 mW Radio frequency 868.4 MHz EU; 869.2 MHz RU; Indoor range up to 45m Outdoor range up to 75m Module dimensions (H*W*D) 18mm*48mm*37mm Minimum battery life 10,000 clicks Degree of protection CH-408 IP-30 4. Briefly about Z-Wave Z technology -Wave is a wireless communication protocol that is used by more than 350 manufacturers to produce more than 2500 different home automation products. ConnectHome devices are guaranteed to be compatible with other Z-Wave devices, as they undergo mandatory certification. The Z-Wave protocol uses a reliable and absolutely secure radio channel. All Z-Wave devices are interconnected in a mesh network (eng. mesh "loop, network cell"), in which various devices can receive and transmit control signals to other network devices using intermediate neighboring nodes. The Z-Wave network has the ability to automatically rebuild data transmission routes, depending on external factors, for example, if there is an obstacle between two neighboring devices, the signal will go through other nodes of the Z-Wave network that are within range. Z-Wave is a two way network. Devices can not only send control commands, but also wait for confirmation of their delivery, as well as request the current state of the device. If the sending was not successful, the system tries to send the command in a different way. The central link of any Z-Wave network is the main controller, it stores information about the network topology, it can be used to add and remove devices from the network. As a rule, the main controller is a device that is connected to the Internet, which allows you to control all devices remotely. 5. Device control The CH-408 device is designed to transfer control commands to other Z-Wave modules using switches connected to it. Both monostable and bistable switches can be connected to CH-408. Monostable switch - a return type switch or button, each press sends a command of your choice to the assigned device. A bistable switch is a switch with two fixed positions On or Off. When the key is pressed (contact closed) - the device sends a command Turn on, when it is released (contact is open) - turn off the command to all devices in the corresponding connection group. To control devices, as well as to assign the type of control commands, you need to add a device to your Z-Wave network and configure it using parameters and adding links. 6. Connecting and configuring the device STEP 1 The device is designed for installation in a standard installation box. The device is powered by a 1/2 AA battery (ER14250) or an alternative power source 12-24V DC (Figure 2). Choose the power supply method and connect the switches according to the diagram. ATTENTION! Simultaneous use of two power sources (battery and alternative power source) is prohibited. WIRING DIAGRAM CH-408: Where: In8 - Switch No. 8; In7 - Switch No. 7; In6 - Switch No. 6; In5 - Switch No. 5; In4 - Switch #4 In3 - Switch #3; In2 - Switch #2; In1 - Switch No. 1; Com - connector for connecting the red wire of the temperature sensor; - - common connector for connecting switches, as well as an alternative power source and blue wire of the temperature sensor; + - connector for connecting an alternative power source; STEP 2 To add a switch to the Z-Wave network, put the controller into learning mode (see your controller's instructions) and hold the system button for 3 seconds. To remove (exclude) the switch from the Z-Wave network, switch the controller to the exclusion mode (see the controller instructions) and hold the system button for 3 seconds. Please note that after the device is excluded from the Z-Wave network, all settings you have made will be reset to factory settings. If you have problems connecting the device to your Z-Wave network, you must go through the process of exclusion from the Z-Wave network, and then repeat the process of adding. STEP 3 Using the main controller of your Z-Wave network, assign the devices that the CH-408 will control. To do this, add controlled devices to the appropriate connection groups, and also select the types of commands that CH-408 will send to controlled devices (To configure connections and parameters, refer to the user manual of your main controller). 7. Links Z-Wave devices can interact with each other, as well as exchange data and other information directly without the participation of the controller, through links. Each event can have its own list of recipients, called a link group. Refer to your Z-Wave controller's user manual for link settings. Some controllers can be automatically added to all link groups. For correct operation, add to the appropriate communication groups only those devices that will be controlled by CH-408, and leave unused groups empty. Attention! CH-408 is a battery operated device. To increase the service life, CH-408 is constantly in sleep mode. After adding devices to link groups, wake up the device by pressing the system button to apply the settings (Figure 2). COMMUNICATION GROUPS CH-408: Group 1 - device (controller recommended) that will receive battery charge reports. The group size is 3 devices. Group 2 - devices that will receive the Scene activation set command. Group size 3 devices. Group 3 - devices that will receive the On / Off command when switch No. 1 is triggered. The group size is 5 devices. Group 4 - devices that will receive the On / Off command when switch No. 2 is triggered. The group size is 5 devices. Group 5 - devices that will receive the On / Off command when switch No. 3 is triggered. The group size is 5 devices. Group 6 - devices that will receive the On / Off command when switch No. 4 is triggered. The group size is 5 devices. Group 7 - devices that will receive the On / Off command when switch No. 5 is triggered. The group size is 5 devices. Group 8 - devices that will receive the On / Off command when switch No. 6 is triggered. The group size is 5 devices. Group 9 - devices that will receive the On / Off command when switch No. 7 is triggered. The group size is 5 devices. Group 10 - devices that will receive the On / Off command when switch No. 8 is triggered. The group size is 5 devices. Group 11 - devices that will receive a command to dim / open (up / down) while holding switch No. 1. The group size is 5 devices. Group 12 - devices that will receive a command to dim / open (up / down) while holding switch No. 2. The group size is 5 devices. Group 13 - devices that will receive a command to dim / open (up / down) while holding switch No. 3. The group size is 5 devices. Group 14 - devices that will receive a command to dim / open (up / down) while holding switch No. 4. The group size is 5 devices. Group 15 - devices, which will receive the command to dim / open (up / down) while holding switch No. 5. The group size is 5 devices. Group 16 - devices that will receive a command to dim / open (up / down) while holding switch No. 6. The group size is 5 devices. Group 17 - devices that will receive a command to dim / open (up / down) while holding switch No. 7. The group size is 5 devices. Group 18 - devices that will receive a command to dim / open (up / down) while holding switch No. 8. The group size is 5 devices. Group 19 - devices controlled by sensor 1. Group size - 5 devices. Group 20 - devices controlled by sensor 2. Group size - 5 devices. 8. Parameters Attention! CH-408 is a battery operated device. To increase service life, CH-408 is constantly in sleep mode. After adding the settings, wake up the device by pressing the system button to apply the settings (Figure 2). Parameter #1 - Setting switch #1 Select the command that will be sent to the 3rd or 11th communication group depending on the state of the switch and its type. 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected (Default); 1 Turn on when pressed / dim up when held. It works when a monostable switch is connected. 2 Bistable button. (Operates when a bistable switch is connected.) Has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent press of the button switches the device from the 3rd group of connections to the opposite state. Holding down the button will send a dimming up/down command to a device in the 11 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter #2 - Switch #2 setting Select the command to be sent to the 4th or 12th link group depending on the state of the switch and its type. 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected (Default); 1 Turn on when pressed / dim up when held. Works when a monostable switch is connected; 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). When this value is selected, dimming does not work. 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent pressing of the button switches the device from the 4th group of connections to the opposite state. Holding down the button will send a dimming up/down command to a device in the 12 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, dimming does not work. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter #3 - Switch #3 setting Select the command to be sent to the 5th or 13th link group depending on the state of the switch and its type. 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected (Default); 1 Turn on when pressed / dim up when held. It works when a monostable switch is connected. 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent pressing of the button switches the device from the 5th group of connections to the opposite state. Holding down the button will send a dimming up/down command to a device in the 13 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter #4 - Setting for button #4 Select the command that will be sent to the 6th or 14th link group depending on the state of the switch and its type. 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected (Default); 1 Turn on when pressed / dim up when held. Works when a monostable switch is connected; 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent pressing of the button switches the device from the 6th group of connections to the opposite state. Holding down the button will send a dim up/down command to a device in the 14 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter #5 - Switch setting #5 Command selection, which will be sent to the 7th or 15th connection group depending on the state of the switch and its type. 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected (Default); 1 Turn on when pressed / dim up when held. Works when a monostable switch is connected; 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent press of the button switches the device from the 7th group of connections to the opposite state. Holding down the button will send a dimming up/down command to a device in the 15th link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). Moreover, The CH-408 will only be able to control one device from the corresponding link group. Parameter #6 - Switch #6 setting Select the command to be sent to the 8th or 16th link group depending on the state of the switch and its type. 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected (Default); 1 Turn on when pressed / dim up when held. Works when a monostable switch is connected; 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent press of the button switches the device from the 8th group of connections to the opposite state. Holding down the button will send a dimming up/down command to a device in the 16 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter #7 - Switch setting #7 Select the command that will be sent to the 9th or 17th link group depending on the state of the switch and its type. 0 Turn off when pressed \ dim downwards while holding. Works when a monostable switch is connected (Default); 1 Turn on when pressed \ dim up while holding. Works when a monostable switch is connected; 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent pressing of the button switches the device from the 9th group of connections to the opposite state. Holding the button will send a dimming up/down command to a device in the 17 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter No. 8 - Switch setting No. 8 Selection of a command that will be sent to the 10th or 18th communication group, depending on the state of the switch and its type (Default); 0 Turn off when pressed / dim down when held. Works when a monostable switch is connected; 1 Turn on when pressed / dim up when held. Works when a monostable switch is connected; 2 Bistable button. It works when a bistable switch is connected. It has two fixed positions: On (contact closed) or Off (contact open). 3 Activation of the scene depending on the state of the switch. Operates when a monostable switch is connected (see scene table). If you select this value, you must add the controller to the 2nd link group; 4 Monostable button switch. Each subsequent pressing of the button switches the device from the 10th group of connections to the opposite state. Holding down the button will send a dimming up/down command to a device in the 18 link group. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. 5 Bistable button switch. (Works when a bistable switch is connected). With its help, you can switch from one possible state to another when you change the position of the switch key. When this value is selected, the CH-408 device must be at a minimum distance from the device that it will control (no more than 10m). In addition, the CH-408 will only be able to control one device from the corresponding link group. Parameter No. 9 - Time of pressing the switch limiting "hold" The parameter specifies the switch hold time, after which the device will send a command to start dimming. Units used in parameter 0.1 second (10 = 1 second). Valid value 1 - 50; 5(Default). Parameter No. 10 - Sending a fixed value when the switch No. 1 is pressed This parameter specifies a fixed value for sending to multilevel devices that are in Connection Group No. 11, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter No. 11 - Sending a fixed value when the switch No. 2 is pressed This parameter specifies a fixed value for sending to multilevel devices that are in Connection Group No. 12, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter No. 12 - Sending a fixed value when the switch No. 3 is pressed This parameter specifies a fixed value for sending to multilevel devices that are in Connection Group No. 13, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter No. 13 - Sending a fixed value when the switch No. 4 is pressed This parameter specifies a fixed value for sending to multilevel devices that are in Connection Group No. 14, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter No. 14 - Sending a fixed value when the switch No. 5 is pressed This parameter specifies a fixed value for sending to multi-level devices that are in Connection Group No. 15, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter #15 - Send fixed value when switch #6 is pressed This parameter specifies the fixed value to be sent to multi-level devices, which are in the Relationship Group No. 16, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter No. 16 - Sending a fixed value when the switch No. 7 is pressed This parameter specifies a fixed value for sending to multilevel devices that are in Connection Group No. 14, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). Parameter No. 17 - Sending a fixed value when the switch No. 8 is pressed This parameter specifies a fixed value for sending to multilevel devices that are in Connection Group No. 18, for example: open shutters by 30%. Valid value is 1 - 99. 0 Disabled (Default). 8.1 Parameters for probe #1 Parameter #20 - Value of probe #1 to turn on Value for multi-level probes, which will be used to turn on devices from the 19th link group. Available settings from -60 to 1000; 0 Default. Parameter #21 - Sensor #1 value to turn off Value for multi-level sensors to be used to turn off
* Attention. Product description can be obtained by machine translation.
